HomeCompany ProfileHistoryProductsContact Us

Accessories

    
Manifolds
   
  
    
Threaded Flanges
   
In case hydraulic cylinders have to be inserted into fixtures, press frames or similar devices, these steel flanges can be very handy.

Material: Weldable steel
  
    
Hydraulic Hoses – HHC
   
Durable but highly flexible thermoplast hydraulic hoses guarantee a very long life.

The four-layer build-up includes 2 layers of high tensile steel fabric and robust fitting with 19mm Hexagon. The volumetric expansion is very low.

Hydraulic hoses model HHC are equipped with a male coupler half as standard.

Standard lengths are as the chart below, further lengths or hoses with larger diameters are quoted on request.
   
Standard 0.5 m
Lengths 1.0 m
2.0 m
3.0 m
4.0 m
6.0 m
8.0 m
10.0m
12.0m
15.0m
   
Safety Factor 4:1 (burst pressure 2800 bar)
100 mm
6.3 mm
Bend Radius
Nominal Width
  
    
Hydraulic Couplers
   
Hydraulic couplers are necessary for the connection of various cylinders to one pump but are also important to offer an axial rotating possibility for the connected cylinder.

Yale hydraulic couplers are self sealing which means that the coupler halves only have to be closed hand tight.

Both female and male parts have inner balls which seal the coupler halves in un-coupled condition, so that no hydraulic fluid will leak.

Please note that all Yale hydraulic cylinders are equipped with the standard female coupler half CFY-1 and dust cap CDF-9.
  
    
Pressure Gauges
  
The use of pressure gauges is recommended when the operating pressure (the force of the connected cylinder) should be monitored.

Yale pressure gauges are equipped with a stainless steel housing and an acrylic plastic face cover plate.

To absorb pressure shocks, gauges are glycerine filled, thus contributing to a long service life. Also, when fitted to a motor pump, the pointer will stay jitter free.

For the calculation of applied cylinder forces, corresponding conversion charts (pressure v force) can be supplied for all Yale hydraulic cylinders.
  
    
GYA-63 Pressure Gauge Set
   
This pressure gauge set is suitable for connection to all HPS hand pumps.

Assembled ready to use, compact design with 45° inclination for easy reading.

Consisting of pressure gauge GGY-632 and corresponding gauge adaptor.
  
    
GA-700/701 – Pressure Gauge Adaptor
   
These pressure gauge adaptors are suitable for connection to all HPS hand pumps.

Gauge connection with sleeve nut and 30° inclination for easy reading.

GA-700 for small pressure gauges
GA-701 for large pressure gauges
  
    
Adaptor Set
   
This pressure gauge adaptor set is suitable for connection to all HPH hand pumps (for double acting cylinders).

To be connected between 4-way valve and hand pump.

Advantage: shows both the pushing force and the pulling force of the connected hydraulic cylinder.

With 30°inclination for easy reading.

Pressureless return by means of the telescopic double nipple.
  
  
GA-2000 – Pressure Gauge Adaptor
   
This pressure gauge adaptor is suitable for Connection to all TWZ hand pumps (2000 bar).

With 30° inclination for easy reading

Suitable for pressure gauge GGY-2500.
   
FULL SPECIFICATIONS AVAILABLE FROM :
CMCO Material Handling (Pty) Ltd

TEL: International: (+ 27 31) 700 4388 or in South Africa: (031) 700 4388
FAX: International: (+ 27 31) 700 4512 or in South Africa: (031) 700 4512

Postal Address: P O Box 15557, Westmead, 3608, South Africa

Or E-Mail us on: sales@cmcosa.co.za
   

 
Copyright by CMCO Material Handling (Pty) Ltd.